FAQ

Version 6 (Dan Smith, 03/09/2012 09:59 am)

1 1 Dan Smith
h1. Frequently Asked Questions
2 1 Dan Smith
3 1 Dan Smith
{{>toc}}
4 1 Dan Smith
5 1 Dan Smith
h2. Cables
6 1 Dan Smith
7 1 Dan Smith
h3. What kind of cable do I need?
8 1 Dan Smith
9 3 Dan Smith
Usually the cable supplied by your radio manufacturer is the highest quality cable you can find. However, it's usually also the most expensive, and is often bundled with software which you may not want or need. There are many 3rd party cables available and they should all work just fine for the most part. Check eBay and "KawaMall":http://www.kawamall.com for cables. Also check the [[CableGuide]] page, which has details about potential pitfalls and some information about cables that are compatible with multiple radios.
10 1 Dan Smith
11 1 Dan Smith
h3. What if my computer does not have a serial port?
12 1 Dan Smith
13 1 Dan Smith
For the most part, USB-to-Serial adapters work without problems. These attach to a USB port and create a virtual serial port that software can use as if it was a regular port. Some adapters are very poor quality and can cause you issues, so if you are experiencing difficulty, you may want to try a different one.
14 1 Dan Smith
15 1 Dan Smith
Without a doubt, the highest quality (and most expensive) adapters come from KeySpan, but you may find that it is worth the money for quality.
16 1 Dan Smith
17 1 Dan Smith
On Windows, determine the COM port that is assigned to the adapter by going into _Device Manager_ and looking under _Ports_.
18 1 Dan Smith
19 1 Dan Smith
h3. Can I use a USB cable?
20 1 Dan Smith
21 1 Dan Smith
Typically, yes. These cables simply have a USB-to-Serial adapter integrated into the cable itself, and are easier to manage and hook up. Follow the same procedures as if you were using a separate adapter.
22 1 Dan Smith
23 1 Dan Smith
*NOTE:* Recently, RTSystems has been selling "Version 4" of their software with a "New USB Cable". It appears that they have specifically designed the cable to be incompatible with other software packages. Beware that if you bought this "new" cable from them you may be unable to use it with CHIRP!
24 1 Dan Smith
25 1 Dan Smith
h3. What if I need to use a COM port other than what is in CHIRP's list?
26 1 Dan Smith
27 1 Dan Smith
You can type anything into the box you need, so if your adapter is assigned to (for example) port 15, simply type +COM15+ into the box and you should be off and running.
28 1 Dan Smith
29 1 Dan Smith
h2. Transferring data between radios
30 1 Dan Smith
31 1 Dan Smith
h3. I have two different radios, how do I transfer data between them?
32 1 Dan Smith
33 4 Dan Smith
CHIRP provides the ability to transfer data between incompatible radios by means of the +Import+ and +Export+ functions. For example, if you have opened a Yaesu VX-8 in CHIRP, you can use the +Import+ function and specify an image from an Icom 2820. A dialog box will open asking you which of the memories from the Icom 2820 you want to import into your VX-8. When the import is complete, you can upload the result to your VX-8. See the [[Beginners_Guide]] for more details about this process.
34 2 Dan Smith
35 2 Dan Smith
h2. Programming your radio
36 2 Dan Smith
37 4 Dan Smith
h3. Should I put my Alinco, Icom, or Kenwood radio into clone mode first?
38 2 Dan Smith
39 4 Dan Smith
No, these radios are well-designed and allow the software to place them into clone mode automatically. This is far more reliable than manipulating the radio by hand and synchronizing the software. Simply plug in your programming cable, power on the radio, and instruct CHIRP to read it.
40 2 Dan Smith
41 2 Dan Smith
h3. Should I put my Yaesu radio into clone mode first?
42 2 Dan Smith
43 2 Dan Smith
Yes, Yaesu radios do not respond to commands over the serial port and must be manually manipulated. Start CHIRP with the cable plugged in and the radio in the intermediate clone mode (usually entered by powering the radio on with one or more buttons pressed). When downloading from the radio, put CHIRP into download mode (where it is waiting on the radio) before initiating the clone out from the radio. When uploading, put the radio into clone receive (or clone wait) mode before initiating the upload from CHIRP.
44 2 Dan Smith
45 1 Dan Smith
h3. What is a live radio?
46 1 Dan Smith
47 1 Dan Smith
Most of the radios supported by CHIRP are programmed by downloading an entire "image" or "snapshot" of the radio's memory, manipulating it, and then uploading it back to the radio. These are called "clone-mode radios". Live mode radios instead communicate with the computer by sending and receiving individual memories one at a time. That means that when you use CHIRP to program them, changes are sent to the radio immediately instead of held until an upload.
48 4 Dan Smith
49 5 Dan Smith
h2. General use
50 5 Dan Smith
51 5 Dan Smith
h3. What are "stock configurations"?
52 5 Dan Smith
53 5 Dan Smith
These are canned frequency plans, some of which are built into chirp. These include standard US calling frequencies, the channelized 60m frequencies, etc. They can easily be opened or imported into your radio from the _File_ and _Radio_ menus.
54 5 Dan Smith
55 5 Dan Smith
h3. Can I add new stock configurations?
56 5 Dan Smith
57 5 Dan Smith
Yes! Adding your group's frequency plan to the stock configurations can make it very quick and easy to program new radios. Further, putting various configurations into the stock list can make switching your radio between multiple functions or geographical regions easy. Simply save a CSV file into the stock configurations directory and restart CHIRP to have it show up in the list. On windows, go to _Start_ -> _Run_ and type:
58 6 Dan Smith
59 5 Dan Smith
 %APPDATA%\CHIRP\stock_configs
60 6 Dan Smith
61 5 Dan Smith
On MacOS or Linux, the path is:
62 6 Dan Smith
63 5 Dan Smith
 ~/.chirp/stock_configs
64 5 Dan Smith
65 4 Dan Smith
h2. Reporting issues
66 4 Dan Smith
67 4 Dan Smith
Refer to the [[How_To_Report_Issues]] page.