Project

General

Profile

Beginners Guide » History » Version 13

Dan Smith, 01/08/2023 09:42 PM

1 9 Dan Smith
# Beginners Guide
2 1 Dan Smith
3 3 Dan Smith
{{>toc}}
4
5 1 Dan Smith
This document should help you get off the ground using chirp and your radio.
6
7 9 Dan Smith
## Before you begin
8 1 Dan Smith
9
Before you begin to use CHIRP with your radio, it is important to understand the two different modes of operation.  Each radio falls into one of two categories:
10
11 10 Dan Smith
12 1 Dan Smith
| *Mode* | *Behavior* |
13 10 Dan Smith
|--------|------------|
14
| Clone | The radio's memories are downloaded or uploaded all at once in a single clone operation. You can download an image of this type of radio, which includes all settings, including memories, VFO state, etc. The radio enters (or must be put into) a special mode of operation while communicating with the PC and is typically power cycled after completion of a transfer. Changes to the memories are made against a saved image, and then are uploaded to the radio. |
15
| Live | The radio remains on and active during communication with the computer.  Memories are transferred one at time from the radio to the computer or from the computer to the radio. Changes to memories are made in real time against the radio as they are entered by the user.  An image of this type of radio cannot be saved to disk in the same way that a clone-mode radio can.  If you want to store the memories in a file, you must export them to a CSV or .chirp file.|
16 1 Dan Smith
17
*Note* that CSV and .chirp files may also be opened and edited directly, but you will not be able to upload directly from those types to any of the radios.  You must always either download from a radio (or open an image of it) first and then Import the contents of your CSV or .chirp file into it before uploading.
18
19 9 Dan Smith
## Basic Procedure for Programming
20 11 Dan Smith
21 9 Dan Smith
### Step 1: Download contents from the radio
22 1 Dan Smith
23 11 Dan Smith
1. Start CHIRP and Click the *Radio* menu and choose *Download From Radio*
24
1. The *Clone* window opens
25 9 Dan Smith
1. Select the serial port you intend to use from the drop down menu
26 11 Dan Smith
1. Select the correct *Vendor* and (if necessary) the appropriate *Model*
27
1. Click *OK* to start the download process.  Clone-mode radios will display a progress bar indicating how much of the image has been downloaded.  Live-mode radios will immediately jump to the memory editor and begin to populate it with memories as they are downloaded from the radio.
28 1 Dan Smith
29 8 Daniel Clemmensen
*Note for Yaesu radios:* There are series of steps that must be followed in order for most Yaesu radios to be properly cloned.  The above process is still accurate, but keep in mind the following:
30 1 Dan Smith
31 11 Dan Smith
* The radio should already be in clone mode before clicking the *OK* button to initiate the download (step 5 above).
32
* After clicking the *OK* button (step 5 above), you should press the button on your radio that initiates the clone transmission.  This is usually indicated on the screen by _Clone TX_ or similar.
33 1 Dan Smith
34 9 Dan Smith
### Step 2: Make changes
35 7 Tom Hayward
36 2 Dan Smith
Once you have the radio contents displayed in the memory editor, you can proceed to make your changes.  This may include manual edits or importing memories from other sources.  If you are using a clone-mode radio, you may wish to save a .img file of your radio as and after you make your changes.  Live mode radio users will have their changes immediately take effect in the radio and do not need to proceed to Step 3.
37 1 Dan Smith
38 9 Dan Smith
### Step 3: Upload changes back to the radio
39 7 Tom Hayward
40 3 Dan Smith
*(For clone-mode radios only!)*
41 1 Dan Smith
42 12 Dan Smith
Once you have made all the edits you need to make, you should upload your image back to the radio.  With your image open, go to the *Radio* menu and choose *Upload To Radio*.  The Vendor and Model are already known, so all you need to do is choose a serial port.
43 1 Dan Smith
44 5 Dan Smith
*Note for Yaesu radios:* Like the download procedure, the upload procedure must follow a particular sequence.  Make sure that your radio is already in clone mode and it is already waiting for an incoming clone transmission.  This is usually indicated on the screen by _Clone Wait_ or _Clone RX_.
45 1 Dan Smith
46 9 Dan Smith
## Other Operations
47 1 Dan Smith
48 9 Dan Smith
### Exporting To A Generic File
49 1 Dan Smith
50
If you wish to save memories from an existing radio out to a generic file that can be imported into other radios or edited by hand, use the Export function in the menu.
51
52 9 Dan Smith
1. Start CHIRP and download a temporary image of your source radio
53
1. Use the Export function to choose a CSV or .chirp file of your radio's contents
54
1. Choose some or all of the memories to export
55 1 Dan Smith
56 9 Dan Smith
### Importing From Another File
57 1 Dan Smith
58 13 Dan Smith
If you have an image from another radio (even another type), you can copy memories from that image to another.
59 1 Dan Smith
60 9 Dan Smith
1. Start CHIRP and download a temporary image of your target radio
61 13 Dan Smith
1. Open the file with the memories you wish to copy
62
1. Choose some or all of the memories to import, and choose *Copy* from the *Edit* menu
63
1. Switch to the tab for your target radio, select the row where the first memory should start and choose *Paste* from the *Edit* menu