Project

General

Profile

CableGuide » History » Version 20

Dan Smith, 04/04/2012 08:51 AM

1 1 Dan Smith
h1. Guide to programming cables
2
3 3 Dan Smith
{{>toc}}
4
5 1 Dan Smith
In most cases, the manufacturer of your radio produces the highest quality cable for programming. However, these are usually the most expensive and are not always the most convenient (because of a lack of USB, etc). Third party cables are available for most radios for a fraction of the cost, but quality can be an issue. Several radios use actual RS-232 signalling and thus cables for these radios can be easily home-built.
6
7 18 Dan Smith
If you have corrections or additions to this page, please "submit":http://chirp.danplanet.com/contact them to me, or ask for edit privileges. I much prefer this information to be user-maintained and contributed!
8
9 4 Dan Smith
*NOTE:* RTSystems has recently been shipping cables intentionally handicapped to prevent their use with third party software, and to prevent use of third party cables with _their_ software. Beware that if you buy their software/cable package, you will not be able to use their cables with CHIRP!
10
11 2 Dan Smith
h2. Alinco Radios
12
13
All (to my knowledge) Alinco radios use a three-pin 1/8" plug with a TTL converter in the 9-pin housing. This is identical to the Icom OPC-478 cable.
14
15 14 Dan Smith
h2. Baofeng
16
17 20 Dan Smith
h3. UV-3R
18 14 Dan Smith
The UV-3R uses a Prolific USB-to-serial chip, but users report that in Windows, you must use drivers from http://409shop.com. It works out of the box on Linux.
19 20 Dan Smith
The PLUS model of the UV-3R uses a Kenwood/Wouxun cable instead of the original single plug cable used by the UV-3R and UV-3R Mark II. All models (thus far) of the UV-3R use the same software
20
21
h3. UV-4X
22
23
The UV-4X is a rebaged UV-3R Mark II and uses the single connector cable. The radios themselves are made by "Vero Telecom":http://www.verotelecom.com/
24
25
h3. UV-5R
26
27
The UV-5R is made by TYT, uses a Kenwood/Wouxun cable, and does not use the same protocol as the UV-3R models.
28 14 Dan Smith
29 1 Dan Smith
h2. Icom Radios
30
31 12 Dan Smith
h3. VHF/UHF Mobiles
32 1 Dan Smith
33
Nearly all of these radios use an OPC-478 (or similar) cable, which plugs into the speaker jack of the radio. The housing of the 9-pin connector has TTL conversion logic, which can be home-built but it is typically easier to buy one pre-made. Note that some of the mobile D-STAR radios can also use their data connection for programming, which uses RS-232 signalling and requires no conversion hardware. Models that can do this include the IC-2820H, ID-880H, and ID-80.
34
35
h3. IC-91AD, IC-92AD, ID-1
36
37
These radios operate in "live" mode and require a full-duplex RS-232 serial cable connection. For the IC-91AD, the OPC-1529 cable is used (and can be easily built).
38
39
The 92AD uses a moisture-proof custom bayonet connection at the top of the radio, which is only available from Icom (OPC-1799) and only with their RS-92 programming software. Note that the OPC-1797 adapter cable will not allow you to use an OPC-478 programming cable with this radio.
40
41
The ID-1 is programmed via its integrated USB connection.
42 2 Dan Smith
43 17 Dan Smith
h3. IC-Q7A
44 16 Dan Smith
45
For some reason, this radio doesn't use the standard three-conductor plug on the OPC-478. The cable for the Yaesu VX-7 actually works perfectly though.
46
47 2 Dan Smith
h2. Kenwood Radios
48
49
h3. TH-F6A, TH-K2A
50
51
These radios use a two-pronged cable that plugs into the microphone and speaker jacks simultaneously.
52
53
h3. TH-D7, TH-D7A, TH-D7Ag
54
55
These radios use a three-pin 3/32" plug directly wired to an RS-232 port (easily home-built).
56
57
h3. TM-D700
58
59
This radio uses a regular serial cable (Female-Female) to the 9-pin connector on the front of the radio.
60
61
h3. TM-D710, TM-V71A
62
63 15 Dan Smith
This radio uses a RS-232 cable (officially, PG-5G) directly cabled to a eight-pin Mini-DIN connector marked "PC" on the back of the radio. No level converter is required, so this can be easily home-made with the right connectors.
64 2 Dan Smith
65
h2. Yaesu Radios
66
67 6 Dan Smith
Check the following recommended vendors for cables:
68
* "KAWA Mall":http://www.kawamall.com/cat_cable_for_yaesu_vertex.cfm
69
* "Valley Enterprises":http://www.valley-ent.com/catalog/yaesuvertex-c-25_45_49.html
70
71 5 Dan Smith
h3. VX-2R, VX-3R, VX-5R, VX-6R, VX-7R, FT-60R
72 2 Dan Smith
73 1 Dan Smith
These handhelds use the same type of cable, which is a four-pin TRRS connector and a TTL voltage converter in the 9-pin housing.
74 5 Dan Smith
75
3rd party cables:
76
* "KAWA Mall":http://stores.ebay.com/KAWAMALL-RAD/Other-/_i.html?_nkw=vx7+cable&submit=Search&_fsub=1&_sid=55765193 : Works for VX-2,3,5,6,7R, ICOM IC-Q7A
77
* "409shop":http://www.409shop.com/409shop_product.php?id=103790 : 2-in-1 cable for these handhelds and FT-7/8xxx mobiles
78 2 Dan Smith
79 10 Dan Smith
h3. VX-8R, VX-8DR
80 2 Dan Smith
81 10 Dan Smith
The VX-8R and VX-8DR both use a moisture-proof multi-pin screw-on connector at the top of the housing. It is recommended that you find a third-party programming cable (not from RTSystems) for this radio. Note that the radio expects 3.3V signalling.
82 1 Dan Smith
83 13 Dan Smith
If you are interested in building a custom cable, see "this guide":http://users.tpg.com.au/vk4go1/vx8-2.htm.
84
85 10 Dan Smith
3rd party cables:
86
* "VX-8R/DR":http://www.valley-ent.com/catalog/yaesu-radio-programming-cable-fdti-chipset-windows-p-226.html from Valley Enterprises
87
88
h3. VX-8GR
89
90 6 Dan Smith
The VX-8GR uses a three-conductor 3/32" plug directly to an RS-232 port. This is the same cable that Kenwood APRS radios use for the GPS connection, and almost the same as the Icom OPC-1529 type data cable, except that a null modem adapter must be used to switch the TX and RX pins.
91
92 7 Dan Smith
3rd party cables:
93
* "VX-8GR":http://www.valley-ent.com/catalog/programming-cable-yaesu-vx8g-series-ct143-ftdi-windows-p-790.html?osCsid=j1ar78gkc6k6f6rueetvrb3pi6 from Valley Enterprises
94 2 Dan Smith
95
h3. FT-7800, FT-7900, FT-8800, FT-8900
96
97
These radios use a 6-pin mini-DIN plug and a TTL converter in the 9-pin housing.
98 8 Dan Smith
99
3rd party cables:
100
* "Valley Enterprises":http://www.valley-ent.com/catalog/yaesu-programming-cable-ft7800-ft8800-ft8900-p-218.html
101 9 Dan Smith
102 11 Dan Smith
h2. Wouxun Radios
103 9 Dan Smith
104 19 Robert Terzi
The KG-UVD1P and UV2, UV3 radios use the same cable as the Kenwood TH-F6A and TH-K2A listed above.  The connection consists of a 3.5 mm and a 2.5 mm 3-conductor phone plug (TRS).  It is a 5 Volt (TTL) serial interface, with Ground and TXD (from Radio) on the sleeve and ring of the 2.5mm connector.  RXD (to radio)is on the sleeve of the 3.5 mm plug.