CHIRP

# How to add a new radio driver

You've got a radio that's not in Chirp, a little bit of software development experience, and you want to add that radio to Chirp. Here's what you'll need:

* a subscription to the [chirp_devel mailing list](http://intrepid.danplanet.com/mailman/listinfo/chirp_devel)

* a Python development environment

* radio

* programming cable

## Setting up the development environment

If you want to develop in another operating system, you're on your own. This guide isn't going to cover it. Here's a guide for Windows: [[DevelopersWin32Environment]].

## Look over some existing code

Read source:chirp/drivers/template.py. The whole thing.

This serves as a starting point for understanding the structure of a driver for a radio that operates in "clone mode", which is by far the most common type of radio and CHIRP driver. If your radio will operate in "live mode", and especially if your radio uses the CAT protocol, you should probably start by reading source:chirp/drivers/kenwood_live.py.

## Write the download/upload routines

### Sniffing the protocol used by existing software

If you have other programming software for your radio, such as the software from the manufacturer, you can sniff the serial programming protocol with [Portmon](http://technet.microsoft.com/en-us/sysinternals/bb896644.aspx). Typically, radio programming software is written for Windows, and Portmon is a Windows utility.

For recent versions of Windows, you might try sniffing USB with [USBPcap](http://desowin.org/usbpcap/). The captured data is analysed with any recent version of [Wireshark](http://www.wireshark.org).

Start with a read.

1. Click Read in the official software

1. Watch the output of Portmon after you click Read

1. Look for a line that sets the BAUD RATE. Sometimes there are a few of them.

1. Look for a WRITE line with a few data bytes. This is probably the command to tell the radio to start sending data.

1. Look for READ lines with lots of data bytes after them. This is probably the memory contents of the radio being downloaded

1. You're a smart developer. You should be able to figure out the protocol from here!

You can also sniff a many Windows programs by running them in the Wine environment under Linux. Manufacturers' radio programming software is likely to run in this environment. See [[DevelopersUSB Sniffing in Linux]].

h3. Using existing Chirp code

If the radio you're developing for doesn't have existing programming software, you won't be able to use the above reverse engineering technique. Most radio manufacturers use a common protocol across most of their radios. Because Chirp supports so many manufacturers, there's a chance an existing radio driver has a download routine that will work with your new radio. This is especially true with Yaesu radios (other than the FT-4/FT-65 family), which don't really even have a protocol. They just dump their memory. All you need to figure out is the baud rate and the memory size (and baud rate is usually 9600).

Choose a radio driver that you think might be similar. If you were going to add the VX9, you might start with the VX8 driver:

```

$ cd chirp/chirp

$ sed s/VX8/VX9/g vx8.py > vx9.py

```

Increase the `_memsize` variable significantly. The goal is to read more data than the radio sends.

Launch Chirp and start a download with your new radio driver. Did it work, sort of? Save the .img.

Now we're going to determine the `_memsize`. Open the .img in a hex editor:

```

$ hexdump -C VX9_oversize.img | less

```

Look towards the end of the file for the offset where the data becomes all zeros. This is your `_memsize`. The radio has stopped sending data, but Chirp was still "reading". Change `_memsize` in your driver so that Chirp reads the same number of bytes the radio is sending.

h2. Map the memory blob

To map the memory layout, you're going to make a small change on the radio, do a download, then look for differences. Do this over and over until you have the whole memory layout mapped.

Here's a little helper script I use for the comparisons:

`hexdiff.sh:`

```

#!/bin/sh

A=`mktemp`

B=`mktemp`

hexdump -C $1 > $A

hexdump -C $2 > $B

diff $A $B | less

rm $A $B

```

1. Find the first channel

1. Find the second channel

1. The offset between the two is your memory channel struct size

1. Find the last channel. Hopefully its offset is struct size * advertised number of channels away from the first channel!

You'll probably start off with something like this:

```

MEM_FORMAT = """

#seekto 0xb00;

struct {

  u32 freq;

  u8 unknown1;

  u8 unknown2;

  u8 unknown3;

  char name[8];

} memory[200];

"""

```

`0xb00` is the location of the first memory channel.

`200` is the number of channels the radio supports.

`unknown1`, `unknown2`, and `unknown3` are for memory-specific settings (e.g., tone) that you haven't sussed out yet.

## Write `get_memory()`

This is called to get your driver to populate the CHIRP memory model with the data for one radio memory. On startup, it’s called once for each memory register you’ve delimited for your radio and once for each special memory. Later it will be called as needed.

* `get_memory()` returns a populated CHIRP memory object that the driver creates as a new instance of the chirp_common.Memory structure. You’ll want to become familiar with the fields in the Memory structure (presently specified in the source tree in the source file `chirp/chirp_common.py`).

* The number of memories is specified in `chirp_common.RadioFeatures.memory_bounds`, which is a pair of numbers (first memory number, last memory number.) `get_memory()` will be called with an integer parameter for regular memories with a value up to the last memory number.

* Special memories are radio-specific channels that can hold special meaning in the radio (such as scan limits, home/call channel, skip channels, etc.) They are specified in your driver as members of the list that you set at `chirp_common.RadioFeatures.valid_special_chans`. `get_memory()` will be called with a string containing the name of the special channel, and you must set the `Memory.number` field of the resulting memory object to an index that is greater than the last memory register number and different than other special memories without holes in the sequence. Subsequent calls to `get_memory()` may receive either the index or the name.

Do read the example driver at `chirp/chirp/drivers/template.py`. There is a commented stub version of this routine in `chirp/chirp.common.py`. Your driver is expected to override it.

## Write `set_memory()`

This is called whenever CHIRP wants your driver to set a memory channel according to the fields described in the specific `chirp_common.Memory` parameter. The driver will presumably need to determine the specific place in the radio's memory based upon the value of `memory.number` (e.g. integer less than or greater than last memory number.) The driver should not change the memory structure.

There is no return value from `set_memory()`.

Do read the example driver at `chirp/chirp/drivers/template.py`. There is a commented stub version of this routine in `chirp/chirp.common.py`. Your driver is expected to overload it.

## Per-memory extra settings

CHIRP can (optionally) manage and display other settings for each memory. These are stored in `chirp_common.Memory.extra`, and are handled by your driver during the `get_memory()` and `set_memory()` by setting or honoring the `extra` field, which should be a `settings.RadioSettingGroup` object.

## Add an image of your radio to the tree

Save it to `tests/images/Vendor_Model.img`

## Run tests

Make sure all the tests pass before you submit:

```shell

$ tox

```

See [[DevelopersPython3Environment]] for more examples of running tests. All the tests must pass before your code can be merged.

## Submit code to github