New Model #2437
Anytone TERMN-8R
Status: | In Progress | Start date: | 03/17/2015 | ||
---|---|---|---|---|---|
Priority: | Normal | Due date: | |||
Assignee: | Jim Unroe | % Done: | 50% |
||
Category: | - | ||||
Target version: | 0.5.0 | ||||
Chirp Version: | daily | Equipment Loan Offered: | Yes |
Associated revisions
[termn8r] Add Anytone TERMN-8R Support #2437
Add basic spreadsheet editor support
Add a few "Function Setup" settings to get started
- Welcome Message (line 1 & line 2)
- Display Mode
- Automatic Power-off
Add an "extra" setting to get started
- Busy Channel Lockout
Bonus: Add equivalent Anytone OBLTR-8R support
Add AnyTone OBLTR-8R and TERMN-8R images
Related to #2437
History
Updated by Jim Unroe almost 4 years ago
- Status changed from New to In Progress
- Assignee set to Jim Unroe
- Target version set to 0.5.0
- Chirp Version changed from 0.4.0 to daily
Updated by Jim Unroe almost 4 years ago
- File AnyTone_TERMN-8R.img added
- File AnyTone_OBLTR-8R.img added
- % Done changed from 0 to 50
Initial AnyTone TERMN-8R driver submitted.
Includes basic spreadsheet editor support and a few settings.
Bonus: AnyTone OBLTR-8R support included.
Jim KC9HI
Updated by Alex B almost 4 years ago
- File chan.PNG added
Guys,
Great job on the new driver.
There is an issue with showing the empty channels after upload.
You need to set the binary flags in address 0101 & 0102 to hide them. Please see the Attached image.
I was trying to figure out the file structure on my own and here are some of the missing pieces:
bbcd freq4;
bbcd offset4;
u8 unknown1:4,
tune_step:4;
u8 unknown2:2,
txdcsextra:1,
txinv:1,
channel_width:2,
unknown3:1, = Talkaround
tx_off:1;
u8 unknown4:2,
rxdcsextra:1,
rxinv:1,
power:2,
duplex:2;
u8 unknown5:4,
rxtmode:2,
txtmode:2;
u8 unknown6:2,
txtone:6;
u8 unknown7:2,
rxtone:6;
u8 txcode;
u8 rxcode;
u8
Optional Signaling:1, 01=DTMF, 02=2Tone, 03 = 5Tone, 04 = MSK
unknown:2,
char name6;
u8 squelch:4,
unknown9:2,
bcl:2; Busy Channel Lockout: 1=Repeater, 2=Busy
u8 unknownA;
5TonePTTID: 0=none, 10=begin, 20=end, 30=Begin & End *
*DTMF PTTID: 0=none, 01=begin, 02=end, 03=Begin & End
u8 unknownB:7,
sqlmode:1; 00=Carrier, 01=CTCSS/DCS
u8 unknown:2, Define CTSS Freq: [62.5 : 254.1]
unknownC 2,
Updated by Jim Unroe almost 4 years ago
Alex,
This is being done. I just added a channel to CHIRP and uploaded the data to the radio. I verified it was there. Then I removed that channel from CHIRP and again uploaded the data to the radio. I verified that the channel was removed.
Please describe the steps that you are using that results in an "unhidden" channel so I can try to duplicate it here.
Jim
Updated by Alex B almost 4 years ago
Jim,
This doesn't happen all the time. But occasionally, if I use OEM Software to program Channels 1, 2 and 3 into the radio, and then delete channel 2 via CHIRP ...the radio (in channel mode) will go through channels 1, 2(empty), 3, 4(empty), 5 (empty) ...all the way to 199(empty).
On an empty channel the radio shows blank screen with only the channel number in the upper right.
Alex
Updated by Alex B almost 4 years ago
Jim,
Please disregard the above for now - cannot duplicate anymore. Don't want you to waste your time.
Thanks,
Alex