Feature #8185
closedTenway UV-5R Pro power levels
Added by Derek Salling over 4 years ago. Updated about 4 years ago.
100%
Description
The Tenway UV-5R Pro has three power levels: High 8W, Medium 4W, Low 1W
In CHIRP, the user can select High or Low power for each channel, but once loaded to the radio, this corresponds to High or Medium power. Low power must be specifically selected by the user if desired, for each channel, on the radio.
Please correct the power level options for this radio to include all three options.
Firmware message during 3+Power-On is: VER BFB298
Firmware listed in CHIRP is: HN5RV01
Happy to provide more info if needed.
Files
| Baofeng_BF-F8HP_20200820.img (6.5 KB) Baofeng_BF-F8HP_20200820.img | Derek Salling, 08/20/2020 11:44 PM | ||
| Tenway_UV-5R Pro_20200820.img (6.5 KB) Tenway_UV-5R Pro_20200820.img | Derek Salling, 08/20/2020 11:44 PM | ||
| Tenway UV-5R Pro Settings.png (22.7 KB) Tenway UV-5R Pro Settings.png | Jim Unroe, 08/21/2020 10:34 AM | ||
| Baofeng_BF-F8HP_20200821.img (6.5 KB) Baofeng_BF-F8HP_20200821.img | Derek Salling, 08/22/2020 12:19 AM |
Updated by Jim Unroe over 4 years ago
- Status changed from New to Feedback
Hi Derek,
You are selecting the wrong model. You should be selecting...
Vendor: Baofeng
Model: BF-F8HP
As shown on the CHIRP "Supported Radio Models":https://chirp.danplanet.com/projects/chirp/wiki/Home list.
Baofeng/Pofung
- BF-F8HP (3 power levels)
Jim KC9HI
Updated by Derek Salling over 4 years ago
Hi Jim,
Thanks for the feedback. Selecting the BF-F8HP and then downloading from my radio does give me control over 3 power levels (have not tried uploading yet, will try that after work today).
However, this introduces a new issue: only the memories tab is accessible; I can no longer view or change the radio settings.
At this point I'm still convinced that specific support for the Tenway UV-5R Pro needs to be improved.
Updated by Jim Unroe over 4 years ago
Derek Salling wrote:
Hi Jim,
Thanks for the feedback. Selecting the BF-F8HP and then downloading from my radio does give me control over 3 power levels (have not tried uploading yet, will try that after work today).However, this introduces a new issue: only the memories tab is accessible; I can no longer view or change the radio settings.
At this point I'm still convinced that specific support for the Tenway UV-5R Pro needs to be improved.
There is 1 or more settings that are out-of-range. Attach a freshly downloaded CHIRP Radio Images (*.img) file so I can investigate them.
Jim KC9HI
Updated by Derek Salling over 4 years ago
Ran into some connection issues this evening... Had three separate errors:
- Radio refused to send second block 0x1f00
- Radio did not respond
- Radio refused to accept block 0x0640
Using a cable with the CH340 driver, so I don't think its the cable, but I'm too new to this to know what to blame.
My freshly downloaded Baofeng BF-F8HP image is attached.
Updated by Derek Salling over 4 years ago
And here is a freshly downloaded Tenway UV-5R Pro image.
Updated by Jim Unroe over 4 years ago
Derek Salling wrote:
And here is a freshly downloaded Tenway UV-5R Pro image.
Derek,
Thanks for attaching a CHIRP Radio Images (*.img) file from your radio. Unfortunately I don't see any problem with it. All the settings tabs display just fine for me. See attached screen capture.
Oh wait. I see the other file now. Standby...
Jim KC9HI
Updated by Jim Unroe over 4 years ago
Derek,
The problem has to do with the TX Power level settings in the VFO. Would you, using the keypad, set VFO A to the MID power level and VFO B to the LOW power level. Then download the changes to CHIRP and attach the downloaded file.
Thanks,
Jim KC9HI
Updated by Derek Salling over 4 years ago
Hi Jim,
I made the suggested changes, and downloaded to CHIRP. See attached file.
It was not quick, as I had a lot of connectivity issues. Since this download I have been unable to make any more uploads or downloads, using either the BF-F8HP or the UV-5R Pro radio selections. I'm thinking more and more that my cable is junk.
Updated by J Gep about 4 years ago
If I may contribute, these are what the settings need to be to support the 3 power levels:
lowpower: 0x01 (......01b) = MED
lowpower: 0x01 (......00b) = HIGH
lowpower: 0x01 (......10b) = LOW
Updated by Jim Unroe about 4 years ago
Derek Salling wrote:
Hi Jim,
I made the suggested changes, and downloaded to CHIRP. See attached file.It was not quick, as I had a lot of connectivity issues. Since this download I have been unable to make any more uploads or downloads, using either the BF-F8HP or the UV-5R Pro radio selections. I'm thinking more and more that my cable is junk.
Derek,
As I expected, manually changing the settings in the radio's VFOs corrected the invalid values stored in them. Now the settings tabs display as they should. All should be good now.
Jim KC9HI
Updated by J Gep about 4 years ago
Are all 3 power levels for the Tenway UV-5R Pro going to be part of native support? I'm manually setting them in the developer section right now.
Updated by Jim Unroe about 4 years ago
J Gep wrote:
Are all 3 power levels for the Tenway UV-5R Pro going to be part of native support? I'm manually setting them in the developer section right now.
You should use the BF-F8HP model selection to get support for 3 power levels.
Jim KC9HI
Updated by Bernhard Hailer about 4 years ago
- Status changed from Feedback to Closed
The issue submitted originally appears to have been resolved.
Updated by J Gep about 4 years ago
Just my opinion, but if I have to select a model other than the Tenway UV-5R Pro in the Chirp software for the full features to be supported, then why is the Tenway UV-5R Pro model a selectable option in Chirp? Shouldn't it default to the BF-F8HP instead? It seems misleading to the users of Chirp to list the Tenway model when you aren't supposed to select the Tenway model to get everything to function correctly.
Updated by Bernhard Hailer about 4 years ago
- Status changed from Closed to Feedback
- Target version set to chirp-legacy
I think you're right. Reopened it so that it can be worked on.
Updated by Jim Unroe about 4 years ago
J Gep wrote:
Just my opinion, but if I have to select a model other than the Tenway UV-5R Pro in the Chirp software for the full features to be supported, then why is the Tenway UV-5R Pro model a selectable option in Chirp? Shouldn't it default to the BF-F8HP instead? It seems misleading to the users of Chirp to list the Tenway model when you aren't supposed to select the Tenway model to get everything to function correctly.
Who ever added the Tenway UV-5R Pro made it an alias of the UV-5R (so it only supports 2 power levels). It needs to be changed to be an alias of the BF-F8HP (so it will support 3 power levels). I just need someone to confirm that when used with the Vendor: Baofeng / Model: BF-F8HP selections, it works properly.
Jim KC9HI
Updated by Derek Salling about 4 years ago
Jim Unroe wrote:
Who ever added the Tenway UV-5R Pro made it an alias of the UV-5R (so it only supports 2 power levels). It needs to be changed to be an alias of the BF-F8HP (so it will support 3 power levels). I just need someone to confirm that when used with the Vendor: Baofeng / Model: BF-F8HP selections, it works properly.
Jim KC9HI
Hi Jim,
Using the Vendor: Baofeng / Model: BF-F8HP selections seems to working OK for me. I'm still a rookie here, so unable to properly explore all functions, but power levels seem to be loading correctly.
I've also moved from a CH340 cable to an FTDI cable; connection is much more reliable.
Updated by Jim Unroe about 4 years ago
- % Done changed from 0 to 100
I just added a patch to alias the Tenway UV-5R Pro with the Baofeng BF-F8HP model instead of the Baofeng UV-5R model. Tri-power support should be in the next CHIRP daily build. In the mean time, use the BF-F8HP selection.
Jim KC9HI
Updated by Jim Unroe about 4 years ago
- Status changed from Feedback to Resolved
- Assignee set to Jim Unroe
Update Status and Assignee
Jim KC9HI
Updated by Anonymous about 4 years ago
- Status changed from Resolved to Closed
Applied in changeset commit:98b8a850b0f1.